性爱小说视频,人人谢人人操,波多野结衣在线观看无码,激情综合激情五月

高壓風機是廣泛應用在各種機械設備上的重要部件，其中對漩渦氣泵進行簡單的維護，可以提高工作效率，對于保障整個生產的正常進行是十分必要的。那么怎樣進行簡單的維護呢？E路風機網小編給你支兩招。

High pressure blower is an important component widely applied to various mechanical devices. The simple maintenance of vortex air pump can improve work efficiency, and is necessary for ensuring the normal operation of the whole production. So how to do simple maintenance? E fan network Xiaobian give you two strokes.

1、對氣泵壓力或流量降低時進行的維護

1. Maintenance of air pump pressure or flow rate

當出現壓力和流量下降時，切斷旋渦氣泵的電源，查看進氣口是否有東西堵塞，檢查進氣口過濾網，不過不要拆除過濾網，否則會把雜物吸進氣泵，導致?lián)p壞。其次，若發現機器內部有雜物的，導致橡膠皮頂住了電磁鐵，造成電磁鐵不能恢復位置。此時可以打開旋渦氣泵的外殼，清理內部雜物。在橡膠皮上鉆一個小孔，排除負壓產生的吸附作用即可。電機的缺相或運轉方向不對也是造成此類故障的一個原因，此時應檢查并重新接好電源，如果電機燒壞，應更換同型號電機，單相電機檢查電容是否完好，接線是否正確。

When pressure and flow rate decrease, first cut off the power supply of the vortex air pump, check whether there is something clogging in the intake port, check the inlet filter net, but do not dismantle the filter screen, otherwise, you will suck the sundries into the air pump and cause damage. Secondly, if it is found that the inside of the machine has sundries, it causes the rubber skin to withstand the electromagnet, causing the electromagnet to be unable to restore the position. At this point, the outer shell of the vortex gas pump can be opened to clean up the internal debris. A small hole is drilled on the rubber skin to remove the adsorption of negative pressure. The motor's missing phase or the wrong direction of operation is also a cause of such a failure. At this time, the power should be checked and re connected. If the motor is burnt out, the same type of motor should be replaced, and the capacitance of the single-phase motor is checked well, and the wiring is correct.

2、對氣泵噪聲變大時進行的維護

2. Maintenance of air pump when the noise is bigger

檢查旋渦氣泵泵體內是否有雜物，如有，則打開外殼,清理內部雜物；其次檢查葉輪是否卡住，此時建議聯系廠家修理，需要重新裝配才能消除故障。第三檢查軸承是否損壞，必要時更換軸承。

First, check whether there is any debris in the vortex pump. If there is, open the case and clean up the internal impurities. Secondly, check whether the impeller is jammed. At this time, it is best to contact the manufacturer for repair, so that it is necessary to reassemble to remove the malfunction. Third check whether the bearing is damaged or if necessary to replace the bearing.

3、對泵體溫升高時進行的維護

3. Maintenance of the temperature of the pump when the temperature rises

檢查進氣口是否堵塞，清洗進氣口過濾網，但不能拆除，否則將會吸進雜物損壞機械設備。請適當保持氣泵的工作時間隙。其次檢查機體內有雜物，打開外殼，清理內部雜物。

First check whether the intake port is blocked, clean the intake filter network, but can not be dismantled, otherwise it will suck into the debris damage mechanical equipment. Please keep the working time gap of the pump properly. Second, check the body in the body, open the outer shell, clean up the internal debris.